DEFINITION:
It is a basic, two-component surface saturation and reinforcement material containing solvent epoxy and conductive compounds and additives that can be modified for construction elements, metal and wood.
USAGE AREAS:
By taking advantage of the porosity of the surface, by absorbing 1 to 1.5 mm according to some places:
-Provides positive properties for the second and third floors to the surface.
-reinforces the surface element within itself.
BEFORE APPLICATION
Surface and application preparations: The surfaces to be applied must be free of all kinds of dirt, oil, rust and moisture. Volatile surfaces are transformed into fixed surface systems with spatula, sandpaper or more stubborn roughnesses by sanding, grinding and wiping methods. The most suitable dust removal and cleaning method is air and water. Another point to be considered is that the surface is free from moisture. Water makes the material unhealthy with a reverse acid reaction. For positive results, metal surfaces are treated with phosphating and antioxidant material before application.
Product preparation:
A and B components are supplied as a set. What needs to be done is to thoroughly mix A and B in the given amounts. A hand mixer can be used for this job. Since the material mixture will start to show an exothermic gel after 20 minutes, it is generally recommended to be consumed between 1.5 and 2 hours; otherwise, material losses or application difficulties may occur. If the mixed amount is too much for the area where the material will be applied, small mixtures made with the ratios specified on the products will solve the problem. The product is thinned with the special PLAS'COLL EPOXY THINNER according to the tool to be applied. Preparations for the application tools: Brush, roller or gun should be kept ready free of water.
APPLICATION
Method of application: The material prepared for use should be consumed within 4 hours at the latest. On porous (porous) surfaces such as concrete, ytong or cracked surfaces, the material should be applied in such a way that it penetrates deeply.
AFTER APPLICATION
Drying time: (20 C) First drying :1-2 hours
Final drying: 5-6 hours Chemical curing: Begins after 24 hours.
Storage of application tools: The product that hardens as a result of chemical reaction may harden on the application tools and cause that tool to not be used again. Therefore, the tool is cleaned with Plas'coll EPOXY THINNER right after the application or during breaks during long applications.
CONSUMPTION
The functional type has a consumption rate of 200 gr to 300 gr/m2, depending on the applied surface and the way of application.
STORAGE
The product has a stock life of 6 months when it is closed in the form of A and B components in which it is sold.
Caution ! :
Approaching the product with fire is dangerous. In case of contact with skin and eyes while working with the product, immediate cleaning with water is highly recommended.
- Plas'coll Antistatic Flooring
1. Definition:
It is an epoxy resin-based, 2-component, self-leveling floor covering system that is conductive according to ASTM F-154, does not accumulate static charge, allows safe, static discharge. Three types of coatings are used in the system:
- AntSt 01(Primary)
- AntSt 02(Intermediate)
- AntSt 03(Topcoat)
2.Application Fields:
It is used to obtain an aesthetically pleasing antistatic floor covering on concrete or cementitious surfaces. It is the most suitable solution for explosive material production facilities, military facilities, operating rooms, production facilities containing flammable solvents.
3.Features:
It is Anti Static Conductor according to ASTM F154. The surface-to-surface ELR is between 10kiloohm and 1000 kiloohm.
It has good mechanical and chemical resistance,
It is impermeable (liquid materials),
It creates a solid and shiny surface,
Coating thickness is adjustable.
Strength :
a.Mechanical:
It is suitable for use on floors subject to normal and moderate mechanical loads.
The product is also excellent physical strength 7 days at the end of 40 to 50 N / mm 2 tensile force strength of 115-120 N / mm 2 is the compression force resistance.
Surface hardness:ASTM D2240(Durometer)Scale 'D75,
Thickness loss in wear (TS 699): 0.018%
Elasticity(DIN 53455): 70%
b.Chemical:
| RESISTANT | ammonia water | glycerine | 3-30% salty |
| <20% | flax oil | 30% sulfuric acid | |
| Oil | milk | soap solution | |
| Beer | <45 caustic soda | silicone oil | |
| n-butyl ether | solution | synthetic thinner | |
| cyclohexane | olive oil | That | |
| diesel oil | paraffin | wine | |
| ethanol<13% | castor oil | xylene | |
| ethylene glycol | pig oil | ||
| vegetable juice | <9% hydrochloric acid | ||
| LIMITED DURABLE | nail polish remover | monochlor benzene | 20% hydrochloric |
| n-butanol | oxalic acid | 30-60% sulfuric acid | |
| 5% acetic acid | perchlorethylene | carbontetra chloride | |
| n-butyl acetate | 5-20% phosphoric acid | trichlor ethylene | |
| >15%ethanol | 3%hydrogen peroxide | 35%formaldehyde | |
| 10% nitric acid | |||
| FLIMSY | amines | methylene chloride | >20%phosphoric acid |
| Chloroform | 16% sodium hypochlorite | >10% nitric acid | |
| >5% acetic acid | >20% hydrochloric acid | >60% sulfuric acid | |
| methanol | phenol |
In the environments specified in the table, the product was kept for 7 days and there was no significant film degradation, except for a maximum of 50% partial degradation.
4. Before application
a) Application Preparations: All equipment should be kept ready as the material gel reaction will start after 20 minutes.
b) Surface Preparation: The concrete surface must have sufficient strength (min. compressive strength 25 N/mm 2 ) (BS-25 AND OVER) and must be dry and clean. The surfaces on which the application will be made must be cleaned of all kinds of oil, dirt, rust, dust and moisture. Necessary surfaces (old painted, unstable surfaces with rotten floors) are grinded with a diamond-tipped wiping device and then the dust is cleaned dry. After cleaning, 1 coat AntSt 01 PRIMER is applied in such a way that it penetrates the surface thoroughly. After 24 hours of chemical hardening, necessary surfaces (cracks, pits and crevices are filled with EPOXY FILLER PASTE and MORTAR MACUN to level it where necessary. After 30 hours of putty drying time, 2 coats (at 1 day intervals) ) AntSt 02 INTERMEDIATE PAINT is applied.
c) Product Preparation: The product is made ready for application by mixing it in the form of A + B in the formulation ratios prescribed by our factory.
d) Application Tools Preparations: The product should be applied with a gun or brush, roller. Special leveling trowel and foam removal rollers are also important.
5.Application:
Application Method (or Forms): The material prepared for use should be applied within 8 hours.
IMPORTANT NOTE for application method:
Leveling:
Since the variable coating thickness that Taç AntSt 03 creates on the surface will affect the antistatic property, rough surfaces must be leveled before coating. For defects exceeding 0.5mm, use MORTAR MACUN mortar made with AntSt 01 Primer (see Taç Epoxy Impregnation technical data sheet). Waiting time between floors:
| +10 ° C | +20 ° C | +30 ° C | ||
| AntSt 01 Primer | min max | 36 hours 6 days | 24 hours 4 days | 12 hours 2 days |
| AntSt 02 Intermediate | min max | 24 hours 7 days | 15 hours 5 days | 10 hours 3 days |
| AntSt 03 Topcoat | min max | 24 hours 7 days | 15 hours 5 days | 10 hours 4 days |
6.After Application:
- a) Drying Time (20 0 C): First drying: 1-2 hours
Final drying: 6-8 hours
Chemical Curing: Begins after 24 hours.
- b) Storage of the Product: It should never be stored as a mixture. Packaging covers should be tightly closed.
- c) Storage of Application Tools: It should be thoroughly cleaned with PLAC'COLL EPOXY THINNER
- d) Storage Conditions: Store in a cool and dry environment, in its original unopened package.
- e) Shelf life: 1 year under the specified storage conditions for unopened boxes.
Curing Times:
| Crown AntSt 03 | +10 ° C | +20 ° C | +30 ° C |
| pedestrian traffic | 3 days | 2 days | 24 hours |
| normal effect | 6 days | 4 days | 2 days |
| heavy impact | 10 days | 7 days | 5 days |
| Chemical Effect | 14 days | 10 days | after 7 days |
7. Consumptions and Coating system:
| Coating System | Product | Consumption |
| Liner | AntSt 01 Primer | From 0.2 to 0.5 kg / m 2 |
| Leveling (if needed) | Epoxy mortar | See. Tac 156 technical sheet |
| conductive layer | AntSt 02 Conductor | 0.10 to 0.15 kg / m 2 |
| top coat | AntSt 03 | binder+quartz sand |
8. Grounding of the floor covering
A-) Placement of Electrodes:
Copper electrodes (with Copper Tapes) are mounted on the corners of the leveled, primed, cleaned surface, with a gap of not more than 10 meters between each, by entering 20-30 cm into the ground. Copper Tapes are extended towards the wall. Depending on local conditions and in order to ensure proper electrical conductivity, the following method is recommended:
Plastic-coated wire (about 4 mm 2 section) is taken approximately 30cm plastic scraped from the end portion of the individual wires are pulled out and the free end of the self-adhesive copper tape floor 20-30C is yerleştirilir.bak in with the band (or electric wires are used) by pulling through the walls of a suitable It is connected to the grounding connection or the main ring. The connection to the main ring or the connection of the copper bands to the grounding line should be made by a specialist electrician.
B-) Placement of Grounding Connections:
If the Electrode Set is to be used, the use of copper strip is not required. Each plate 100m 2 's may provide conductivity. Make sure that the distance between the two plates is at most 10m. For longer distances, it is necessary to use a copper strip in between. Carefully clean the grounding plates. Connecting the plates to the main ring must be done by a specialist.
Number of ground connections:
Each area of 100m 2 must be grounded separately. The optimum grounding connection should be determined depending on local conditions and should be indicated by drawing.
Application of Tac AntSt 02 Midcoat:
Plas'coll AntSt Arakat is applied with a brush or roller. It is recommended to test the conductivity.
Attention: Apply Plas'coll AntSt 02 Intermediate Coat after the primer layer is completely dry. Otherwise, creases and the effect of conductivity property may be seen in this layer. Never blunt with conductive solid sand.
Final Coat:
The mixed Plas'coll AntSt 03 is poured onto the surface, pulled with a notched trowel and applied in a thickness of approximately 1.5mm. The air inside is removed with a hedgehog roller.
- Plas'coll Epoxy Primer Paint
1-DESCRIPTION: It is a two-component, reaction-drying, epoxy-based paint containing zinc phosphate and zinc chromate, which prevents corrosion, has high chemical resistance. It has a matte appearance.
a) Places of Use: It is used to protect tanks, cranes and steel constructions against corrosion in all kinds of industrial facilities exposed to acids and alkalis.
b) Amount of Solid Matter: 82% + 3 (by weight)
c) Specific Gravity: 1.75 + 0.1 gr/cm3
d) Packaging Type: A.Comp. in 24/1 tin
B.Comp. in 6/1 cans
2- BEFORE APPLICATION:
a) Metallic surfaces on which Plas'coll Epoxy Primer will be applied must be clean and dry, and the surface must be free of all kinds of oil, dirt and rust.
b) Mixing Ratio: 6 Part A.Comp. with 1 Part B.Comp. is mixed. This mixture should be used within 8 hours.
c) Product Preparation: Epoxy Primer paint is brought to the appropriate viscosity with “Plas'coll Industrial Thinner”.
3- APPLICATION:
a) Application Method: Product application should be done with a gun and brush.
4- AFTER APPLICATION
a) Drying Time: (at 20 C) First drying: 30-45 minutes
Final drying: 4-5 hours
Chemical Curing: Begins after 24 hours
b) Storage: It should be stored in a closed form, in places not exposed to direct sunlight.
c) Considerations: The fire hazard class is II according to the Swedish standard. Since it is a flammable material, it should be kept away from naked flames and should be worked in ventilated environments.
4-CONSUMPTION: (consumption)
7-8 m2 area can be painted with 1 liter.
- Plas'coll Epoxy Impregnating Varnish
PROPERTIES:
a) Content (Contents): It is a solvent-based epoxy based, two-component surface saturation and reinforcement material that can be modified for construction elements, metal and wood.
b) Places of Use: By taking advantage of the porosity of the surface, by being impregnated with 1 to 1.5 mm according to some places:
-Provides positive properties for the second and third floors to the surface.
-reinforces the surface element within itself.
-Prevents corrosion depending on the type of substrate. This corrosion is caused by bacterists and mold inhibitors (imidazole, isomeric ketothiazole and s-triazime derivatives) on wooden surfaces and bacteria-producing environments, in operating rooms, and by zinc-rich oxidation inhibitors on metal surfaces.
-Prevents mosaic dusting.
The cathodic effect of these inhibitors has the ability to prevent the metal from rusting even as a result of minor scratches. Thus, it can be ensured that the metal parts remain intact during long shipment and stock periods before and after assembly.
The main problem of metal surfaces is adhesion. First of all, PLAS'COLL EPOXY IMPRESSED VARNISH provides this adhesion perfectly.
It can be used in all kinds of concrete, ytong, gas concrete, old concrete, brick, briquette, roof elements, modular building elements, both as the first layer of epoxy or for isolation purposes alone.
It is a corrosion preventive material with high adherence on construction elements alone and on metal elements such as tanks, radiators and sheet metal.
It can be used successfully in wooden ship parts and furniture with its high penetration and anti-mildew properties.
PLAS'COLL EPOXY IMPRESSED VARNISH is produced in 3 types according to the place of use.
1)PLAS'COLL BETOMER IMPRESSION: It is a type with small molecule size and high peniteration for building surfaces.
2)PLAS'COLL METAMER ZİNCH RİCH IMPRENYE: It is zinc rich type that provides anticorrosive and cathodic effect for metal surfaces.
3) PLAS'COLL WOOD IMPREGNATION: It is a mold-preventing type containing bactericide for wooden surfaces.
It is also possible to formulate antistatic, hygienic, isolated, anticondensed systems for different types of applied surfaces and different functions.
c) Colors: It consists of the colors of the transparent and functional raw material according to the type.
d) Packing: A COMP B COMP
PLAS'COLL BETOMER 15kg 10kg
TYPE 2 PLAS'COLL METAMER 30kg 3kg
TYPE 3 PLAS'COLL WOOD 25kg 5kg
Packaging shapes also differ in antistatic, anticondensed, hygienic, isolated formulations.
BEFORE APPLICATION:
a) Surface and application preparations: The surfaces to be applied must be free of all kinds of dirt, oil, rust and moisture. Volatile surfaces are transformed into fixed surface systems by spatula, sandpaper or more stubborn roughnesses by sanding, grinding and wiping methods. The most suitable dust removal and cleaning method is air and water. Another point to be considered is that the surface is free from moisture. Water makes the material unhealthy with a reverse acid reaction. For positive results, metal surfaces are treated with phosphating and antioxidant material before application.
b) Product preparation: A and B components are given as a set. What needs to be done is to thoroughly mix A and B in the given amounts. A hand mixer can be used for this job. Since the material mixture will start to show an exothermic gel after 20 minutes, it is generally recommended to be consumed between 1.5 and 2 hours; otherwise, material losses or application difficulties may occur. If the mixed amount is too much for the area where the material will be applied, small mixtures made with the ratios specified on the products will solve the problem. The product is thinned with the special PLAS'COLL EPOXY THINNER according to the tool to be applied.
c) Preparations for application tools: Brush, roller or gun should be kept ready free of water.
APPLICATION:
a) Application method (or forms): The material prepared for use should be consumed within 4 hours at the latest. On porous (porous) surfaces such as concrete, ytong or cracked surfaces, the material should be applied in such a way that it penetrates deeply.
b) Points to be considered: Approaching the product with fire is dangerous. In case of contact with skin and eyes while working with the product, immediate cleaning with water is highly recommended. For detailed material warning information, please refer to the epoxy and polyurethane material warning information sheet.
AFTER APPLICATION:
a) Drying time: (20 C) Initial drying: 1.5-2 hours
Final drying: 5-6 hours
Chemical curing: It starts after 24 hours.
b) Storage of the product: The product has a 6-month stock life as the A and B components in which it is sold.
c) Storage of application tools: The product that hardens as a result of chemical reaction may harden on the application tools and cause that tool to not be used again. Therefore, the tool is cleaned with PLAS'COLL EPOXY THINNER right after the application or during breaks in long applications.
CONSUMPTION:
The functional type has a consumption rate of 130 gr to 400 gr/m2, depending on the applied surface and the way of application.
- Plas'coll Epoxy Topcoat
PROPERTIES:
Contents: It is a two-component, epoxy resin-based glossy paint. It dries by reaction.
Application areas: Chemical plant in extreme acidic or basic environment, often need to be cleaned in place regarding the structure, special machines required mechanical strength requirements, in techisat and structure, can be used in clean rooms. PLAS'COLL EPOXY TOPCOAT, which can be formulated and diversified even after chemical and physical determination, has a 0 (zero) water absorption percentage, so it prevents bacteria from accumulating in one piece, without holes. It is hygienic. Water Absorption rate is 0 (zero).
Packaging Type: A.Comp. in 21/1 tin
B.Comp. in 7/1 cans
Colors: It is produced in 5 main colors as gray, white, black, o.yellow, o.red, and the desired RALL colors can be produced.
d)Packaging: It is as written on it according to its functionality.
BEFORE APPLICATION:
a ) Surface and application preparations: The surfaces to be applied must be cleared of all kinds of dirt, oil, rust and moisture. Volatile surfaces are transformed into fixed surface systems by spatula, sandpaper or more stubborn roughnesses by sanding, grinding and wiping methods. The most suitable dust removal and cleaning method is air and water. Another point to be considered is that the surface is free from moisture. For positive results, metal surfaces are treated with phosphating and antioxidant material before application.
b) Product preparation: A and B components are given as a set. What needs to be done is to thoroughly mix A and B in the given amounts. A hand mixer can be used for this job. Since the material mixture will start to show an exothermic gel after 20 minutes, it is generally recommended to be consumed between 1.5 and 2 hours; otherwise, material losses or application difficulties may occur. If the mixed amount is too much for the area where the material will be applied, small mixtures made with the ratios specified on the products will solve the problem. PLAS'COLL EPOXY PRIMER (first coat) must be applied to the application surface and given 1 day drying time.
c) Preparations for application tools: Brush, roller or gun should be kept ready free of water.
APPLICATION:
Application method (or forms): The material prepared for use should be consumed within 2 hours at the latest. It can be applied by bringing it to the appropriate consistency with the help of a brush, roller or gun. Points to note: Approaching the product with fire is dangerous. In case of contact with skin and eyes while working with the product, immediate cleaning with water is highly recommended. For detailed material warning information, please refer to the epoxy and polyurethane material warning information sheet.
AFTER APPLICATION:
a) Drying time:
(20 C) Initial drying: 1.5-2 hours
Final drying: 5-6 hours
Chemical curing: It starts after 24 hours.
b) Storage of the product: The product has a 6-month stock life as the A and B components in which it is sold.
c) Storage of application tools: The product that hardens as a result of chemical reaction may harden on the application tools and cause that tool to not be used again. Therefore, the tool is cleaned with PLAS'COLL EPOXY THINNER right after the application or during breaks in long applications.
CONSUMPTION:
Depending on the applied surface and the way of application, 1 lt. 7-8 m2 area can be painted with PLAS'COLL EPOXY TOPCOAT
- Plas'coll Solvent Free Epoxy Topcoat
Description: It is a solvent-free, two-component, epoxy based topcoat paint.
Features: Since it does not contain solvent, it provides ease of application, especially in closed areas. It is non-toxic, does not cause poisoning. It allows film application up to 400 microns in a single layer. There is no decrease in film performance as there is no solvent evaporation. It has a very high chemical resistance. It shows excellent resistance to alkalis, acids, water, oil and solvents. It looks shiny.
Areas of Use: It is used in the ship industry, petrochemical facilities, facilities exposed to sea water, chemical tanks and all kinds of facilities in contact with chemicals, and for painting the installations related to drinking water.
Solids Amount: 100%
Specific Gravity: 1.3 + 0.1 gr/cm3
Product Preparation: Part 5 A. Comp. with 1 Part B. Comp. is mixed. The mixture should be used without thinning within 8 hours.
Application Method: The product should be applied with a brush and roller.
Drying Time: Initial drying: 2 hours
Final drying: 6-8 hours
Chemical curing: after 24 hours
Consumption: With 1 liter, 10-18 m2 area can be painted according to the application thickness.
Packaging: A. Comp. Comp. in 25/1 tin. in 6/1 tin
- Plas'coll Water Based Epoxy Primer
PROPERTIES:
a) Contents: It is a two-component, WATERPROOF EPoxy resin-based primer paint.
b) Thanks to the liquid phosphate compounds it contains, TCP has the feature of delaying combustion and not spreading fire. In addition, it ensures that the paint consisting of heat and chemical acids does not dissolve (marblenization) in steamy working environments. It dries by reaction.
c) Places of Use: It can be used easily in chemical plants, in extremely acidic or basic environments, in related parts of structures that need to be cleaned frequently, in special machinery, equipment and structures that require mechanical resistance, and in clean rooms.
d)Packaging: It is as written on it according to its functionality.
BEFORE APPLICATION:
a) Surface and application preparations: The surfaces to be applied must be free of all kinds of dirt, oil, rust and moisture. Volatile surfaces are transformed into fixed surface systems by spatula, sandpaper or more stubborn roughnesses by sanding, grinding and wiping methods. The most suitable dust removal and cleaning method is air and water. Another point to be considered is that the surface is free from moisture. For positive results, metal surfaces are treated with phosphating and antioxidant material before application.
b) Product preparation: A and B components are given as a set. What needs to be done is to thoroughly mix A and B in the given amounts. A hand mixer can be used for this job. Since the material mixture will start to show an exothermic gel after 20 minutes, it is generally recommended to be consumed between 1.5 and 2 hours; otherwise, material losses or application difficulties may occur. If the amount of mixing will be too much for the area where the material will be applied, small mixtures made with the specified ratios on the products will solve the problem. The product is thinned with water according to the tool to be applied.
Preparations for application tools: Brush, roller or gun should be kept ready free of water.
APPLICATION:
Application method (or forms): The material prepared for use should be consumed within 2 hours at the latest. It can be applied by bringing it to the appropriate consistency with the help of a brush, roller or gun.
In case of contact with skin and eyes while working with the product, immediate cleaning with water is highly recommended. For detailed material warning information, please refer to the epoxy material warning information sheet.
III. AFTER APPLICATION:
Drying time: (20 C) Initial drying: 1.5-2 hours
Final drying: 5-6 hours
Chemical curing: It starts after 24 hours.
b) Storage of the product: The product has a 6-month stock life as the A and B components in which it is sold.
c) Storage of application tools: The product that hardens as a result of chemical reaction may harden on the application tools and cause that tool to not be used again. Therefore, immediately after the application or during breaks in long applications, the tool is cleaned with HOT WATER.
CONSUMPTION:
Depending on the applied surface and the way of application, 1 lt. PLAS'COLL WATER BASED EPOXY PRIMER 15-20 m 2 area can be painted with EMPRENYE
- Plas'coll Water Based Epoxy Topcoat
PROPERTIES:
a) Content (Ingredient): It is a two-component, WATER-PROOF epoxy resin-based glossy paint. Thanks to the liquid phosphate compounds it contains, TCP has fire retardant and fire retardant properties. In addition, it ensures that the paint consisting of heat and chemical acids does not dissolve (marblenization) in steamy working environments. It dries by reaction.
b) Places of Use: It can be used easily in car parks, chemical plants, extremely acidic or basic environments, in related parts of structures that need to be cleaned frequently, in special machinery, equipment and structures that require mechanical resistance, and in clean rooms.
PLAS'COLL EPOXY TOPCOAT, which can be formulated and diversified after chemical and physical determination, is basically produced in 1 type.
Plas'coll Water Based Epoxy Topcoat Paint for structures, metal and wood surfaces
c) Colors: It is produced in 5 main colors as gray, white, black, o.yellow, o.red, and the desired RALL colors can be produced.
d)Packaging: It is as written on it according to its functionality.
BEFORE APPLICATION:
a) Surface and application preparations: The surfaces on which the application will be made must be cleared of all kinds of dirt, oil and rust. It is moisture tolerant. Volatile surfaces are transformed into fixed surface systems by spatula, sandpaper or more stubborn roughnesses by sanding, grinding and wiping methods. The most suitable dust removal and cleaning method is air and water. For positive results, metal surfaces are treated with phosphating and antioxidant material before application.
b) Product preparation: A and B components are given as a set. What needs to be done is to thoroughly mix A and B in the given amounts. A hand mixer can be used for this job. Since the material mixture will start to show an exothermic gel after 20 minutes, it is generally recommended to be consumed between 1.5 and 2 hours; otherwise, material losses or application difficulties may occur. If the mixed amount is too much for the area where the material will be applied, small mixtures made with the ratios specified on the products will solve the problem. The product is diluted with water according to the tool to be applied. PLAS'COLL WATER-BASED EPOXY PRIMER (first coat) must be applied to the surface to be applied, and it should be given 1 day drying time.
c) Preparations for application tools: Brush, roller or gun should be kept ready free of water.
APPLICATION:
Application method (or forms): The material prepared for use should be consumed within 2 hours at the latest. It can be applied by bringing it to the appropriate consistency with the help of a brush, roller or gun. In case of contact with skin and eyes while working with the product, immediate cleaning with water is highly recommended. For detailed material warning information, please refer to the epoxy material warning information sheet.
AFTER APPLICATION:
a) Drying time: (20 C) Initial drying: 1.5-2 hours Final drying: 5-6 hours Chemical hardening: 24 hours.
b) Storage of the product: The product has a 6-month stock life as the A and B components in which it is sold.
c) Storage of application tools: The product that hardens as a result of chemical reaction may harden on the application tools and cause that tool to not be used again.
CONSUMPTION: Depending on the applied surface and the method of application, 1 lt. 7-8 m 2 area can be painted with PLAS'COLL WATER BASED EPOXY TOPCOAT.
- Plas'coll Road Marking Paint
Description: It is a two-component, urethane-based topcoat paint that is extremely resistant to water, moisture, acid, alkali, salt water, mineral oils, chemical solvents, outdoor weather conditions and SO 2 . Its appearance is bright.
Areas of Use: All kinds of industrial facilities, petrochemicals and refineries, valuables, machine parts, etc. used in places.
Amount of Solid Matter: 58% + 3 (By Weight)
Specific Gravity: 1.15 + 0.1 gr/cm3
Product Preparation: Part 2 A. Comp. with 1 Part B. Comp. is mixed. This mixture should be used within 8 hours.
Thinning: Plas'coll Polyurethane Topcoat Paint is reduced to the appropriate viscosity with a special polyurethane thinner.
Method of Application: The drill is done with a gun.
Drying Time (at 20°C): First drying: 0.5-1 hour
Final drying: 4-5 hours
Chemical curing: 24 hours
Consumption: An average of 12-14 m2 area can be painted with 1 liter.
Storage: It should be stored in a closed place, out of direct sunlight.
Considerations: The fire hazard class is II according to the Swedish standard. Since it is a flammable material, it should be kept away from naked flames and should be worked in ventilated environments.
Packaging: A. Comp. Comp. 20/1 in tin. in 10/1 tin